Adapters & Anchoring

 

CHROMATE GOLD–PLATED DRIVE–OVER BASES (SET OF 4)
#784212 (173 lbs), Fits 27″ TreadwaysChromate

 

 

 

 

 


 

 

PLATED UPRIGHT HOLDERS (SET OF 4)
Set of 4 uprights, includes 4 bolts and retaining bottom platePlatedUprightHolders
#784213 (140 lbs)

 

 

 

 


 

 

PLATED MEASURE RITE™ UNIBODY TIE-DOWNS
5 heights from bed to top of pinch weld – 12.5″, 14.5″ and 15.5″PlatedMeasureRiteTieDowns
#784210 (76 lbs)

 

 

 

 


 

 

CORVETTE
Special adapters for Corvettes. (Set of 4) Tops only fit onto your existing Measure Rite™ tops.Corvette
#784157 (35 lbs)

 

 

 

 

 


 

 

HONDA/ACURA
Fits all four families of Honda cars. Holds horizontal rocker pinch-welds plus on 1991 and newer models, supports the vehicle by holding the vertical jacking tab.Set includes 4 clamps with bolts, nuts and washers; 4 jacking tab brackets; 12 jacking tab spacer plates.HondaAcura
#784125 (126 lbs)

 

 

 

 

 


 

 

BMW & MERCEDES ’94 & NEWER
Shaft fits into jacking holes and the round or oval on the support bracket fit into support holes in the chassis, which are the strongest points of the car, providing a secure, positive hold. Fits all families of BMW and ’94 – ’03 Mercedes cars. Set includes: 4 adapters with bolts, nuts, and washers; 4 jacking hole shafts with locking collars; 4 round support mounts; 4 oval support mounts.
#784130 (130 lbs)BMW_Mercedes

 

 

 

 

 

 

 


 

 

SUV & Truck Anchoring System

SUV_TruckAnchoring_photo1Quick Ratchet Truck & SUV Anchoring System
The most efficient method of anchoring full frames. The ratchet & strap design create a positive anchor even in the tightest spaces. The versatility of the Pivot Assemblies and Truck Holders ensure that even the toughest frames can be anchored.

Includes

(2) Right Pivot Shaft Assembly, #685000
(2) Left Pivot Shaft Assembly, #685010
(2) Left Truck Holder, #241905
(2) Right Truck Holder, #241915
(4) Ratchet Assembly, #685005
(4) 4″ Strap, 96″ Long, #241935
(4) 4″ Strap, 48″ Long, #241930
(4) Truck Extension, #241855
(1) Chrome Winch Bar, #241879

 


 

Setting Up the System on a Straight Rail

 

 

STEP 1

A_Step1
Place the eye of the nylon strap around the upright of the Truck Holding System.
Slide the Ratchet Assembly into the Drive-over Base.
A. Truck Holder
B. Upright
C. Truck Extension
D. Strap Eye
E. Ratchet Assembly
F. Drive-Over Base

 

 


 

STEP 2A_Step2

 

Wrap the Nylon Strap over the vehicle’s frame rail, push the strap through the Ratchet and use the Chrome Winch Bar to tighten up the strap.
A. Example of a Frame Rail
B. Strap Eye

 

 

 


 

STEP 2 (ALTERNATIVE “LOOP” METHOD)

 

This is an example of an alternative method of “Looping” the eye to clear low obstacles such as running boards. Simply feed the strap through the eye before pushing the strap through the ratchet.
Note: It might be necessary to rotate the Ratchet Assembly 180 degrees to help clear low obstacles.A_Step2b

A. Example of a Frame Rail
B. Strap Eye

 

 

 

 

 

 


 

 

STEP 3

A_Step3

After tightening up the Nylon Strap, use a chain binder to help support the Truck Holding System to the bed of the frame rack.

A. Chain Binder

 

 

 

 

 


 

Setting Up the System on an Angled Rail

In these examples the Right & Left Pivot Shaft Assemblies are shown. The Pivot Shafts were designed to accommodate frame rails that are angled, such as near the wheel well.

 

STEP 1

Place the eye of the nylon strap around the upright of the Truck Holding System.
Slide the Ratchet Assembly into the Drive-over Base.

B_Step1
A. Example of a Frame Rail
B. Pivot Holder
C. Strap Eye
D. Ratchet Assembly

 

 

 

 

 


 

STEP 1 (ALTERNATIVE “LOOP” METHOD)

 

This is an example of an alternative method of Looping” the eye to clear low obstacles such a running boards.
Simply feed the strap through the eye before pushing the strap through the ratchet.

B_Step2 B_Step1b
A. Example of a Frame Rail
B. Strap Eye
Note: It might be necessary to rotate the Ratchet Assembly 180 degrees to help clear low obstacles.
C.Example of Ratchet turned 180 degrees

 

 

 


 

STEP 2 & 3

After tightening up the Nylon Strap, use a chain binder to help support the Truck Holding System to the bed of the frame rack.

B_Step3
A. Chain Binder